gemellocattivo.com http://gemellocattivo.com/forum/ |
|
Autoclave http://gemellocattivo.com/forum/viewtopic.php?f=11&t=328 |
Page 1 of 1 |
Author: | mk e [ Tue Feb 12, 2019 2:34 pm ] |
Post subject: | Re: Autoclave |
damn it, hes says someone it picking it up tonight but he'll let me know if the guy is a no-show. |
Author: | MerlinTech [ Tue Feb 12, 2019 5:20 pm ] |
Post subject: | Re: Autoclave |
Hell yeah, I am liking what you are thinking. |
Author: | TheDarkSideOfWill [ Sun Feb 17, 2019 1:05 pm ] |
Post subject: | Re: Autoclave |
Because everyone needs an autoclave. Wheels OTOH... there's a LOT of engineering that goes into wheels and even more that goes into composite wheels. I just happened to watch this this morning: https://www.youtube.com/watch?v=PGGiuaQwcd8 IOW, I don't think I'd want to try composite wheels without them being designed by a composites engineer who understands how to design composite structures against specific load cases AND thoroughly modeled by someone who knows what they're doing in wheel modeling. A destructive test or two to verify the model's predictions would also be welcome. The consequences of failure in that structure are pretty severe and FRP engineering is complicated. |
Author: | mk e [ Sun Feb 17, 2019 2:26 pm ] |
Post subject: | Re: Autoclave |
Blah, blah, blah.....isn't safe blah, blah Not that you're wrong I watched that video...its what convinced me to give it a go. https://youtu.be/OynKbfEGV_A |
Author: | MerlinTech [ Mon Feb 18, 2019 7:59 am ] |
Post subject: | Re: Autoclave |
mk e wrote: Blah, blah, blah.....isn't safe blah, blah Not that you're wrong I watched that video...its what convinced me to give it a go. https://youtu.be/OynKbfEGV_A Of coarse you did. How hard can it be? Somebody has done it, why not Mark? I get it, why pay for what you can do? Makes perfect sense. |
Author: | mk e [ Mon Feb 18, 2019 10:11 am ] |
Post subject: | Re: Autoclave |
To Wil's point though my though is I'll make at least 1 in WAY cheaper fiberglass to get the laying up sorted and if I think it's a good wheel then I break it and cut it open to be sure it was good......then the real ones. That's the plan anyway. |
Author: | kkrace [ Thu Mar 07, 2019 11:17 am ] |
Post subject: | Re: Autoclave |
I have a whole package of rock wool insulation I can donate. I got it for a powder coating oven I was planning on building. I also just got rid of a 275 oil tank that was in great shape. Sold it to some guy that is turning it into a BBQ grill. I was trying to figure out how much it was going to cost me to make it go away and then a friend told me to try and sell it. Had 10 calls in the first couple hours of guys begging to buy it and haul it away. I also have a friend that follows your v12 build that's a used lab equipment dealer that probably has dozens of used ones if you want to just buy one? |
Author: | mk e [ Thu Mar 07, 2019 9:25 pm ] |
Post subject: | Re: Autoclave |
Hmmmm.......I've back burnered this a little but this is interesting and very generous of you. Let me get through the weekend and get my new used dyno rollers home and see where I am. |
Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |