Well crap. I don't think she likes your car very much.
| gemellocattivo.com http://gemellocattivo.com/forum/ |
|
| FrankenFerrari - V12 ferrari 308 part 4 http://gemellocattivo.com/forum/viewtopic.php?f=2&t=319 |
Page 226 of 226 |
| Author: | mk e [ Sat Jun 29, 2024 10:51 am ] |
| Post subject: | Re: FrankenFerrari - V12 ferrari 308 part 4 |
mk e wrote: Mostly finished painting the kitchen last night.....now either I get a summer break and can play cars or I have more floor to refinish over the coming 2-3weeks then play cars. It appears I will be staying on floor refinishing for the next couple weeks. Such is life |
|
| Author: | MerlinTech [ Mon Jul 01, 2024 6:25 am ] |
| Post subject: | Re: FrankenFerrari - V12 ferrari 308 part 4 |
Well crap. I don't think she likes your car very much.
|
|
| Author: | mk e [ Mon Jul 01, 2024 8:42 am ] |
| Post subject: | Re: FrankenFerrari - V12 ferrari 308 part 4 |
MerlinTech wrote: Well crap. I don't think she likes your car very much. Ferrari is the f word in this house. Lana works very hard to come up with ways to keep me out of the shop because odd charge card expenses follow...imagine her "surprise" when the gasket bill arrived even though I hadn't been in the shop for months  I started with the drum sander yesterday and its going pretty well. Hopefully the floor will be done and drying y the end of the holiday weekend. Some painting will no doubt follow as it did on side 1 so maybe through the following weekend before I'm free and maybe running in August? |
|
| Author: | n2zon [ Mon Jul 01, 2024 8:18 pm ] |
| Post subject: | Re: FrankenFerrari - V12 ferrari 308 part 4 |
mk e wrote: MerlinTech wrote: Well crap. I don't think she likes your car very much. Ferrari is the f word in this house. Lana works very hard to come up with ways to keep me out of the shop because odd charge card expenses follow...imagine her "surprise" when the gasket bill arrived even though I hadn't been in the shop for months I started with the drum sander yesterday and its going pretty well. Hopefully the floor will be done and drying y the end of the holiday weekend. Some painting will no doubt follow as it did on side 1 so maybe through the following weekend before I'm free and maybe running in August? I did most of our house's floors with a drum sander. Upside: They're *fast*! Downside: They're harder to keep under control so you don't divot and they can remove more material than necessary, which limits the number of future refinishings. This is particularly true of softer woods (most of our floors are Douglas Fir). I tried one of the 2-pad orbital floor sanders for the last couple of rooms. A bit slower but *much* easier to control and removes less material unless you're really, really good with a drum sander or you have hardwood floors and don't get too aggressive with sandpaper grades. If you're doing great with the drum sander, carry on! If on the other hand you're a mere mortal like me, consider renting the orbital one. |
|
| Author: | mk e [ Mon Jul 01, 2024 11:01 pm ] |
| Post subject: | Re: FrankenFerrari - V12 ferrari 308 part 4 |
Yes to all the sander thoughs. What I have is prefinished oak...red oak to be specific which is important later. The finish on refinished contains aluminum oxide, so it's really hard. And even though our boards are "square 4 sides", not beveled, the long sides they put fair large radius so it's hard to see, but the edges sit low by at least 20 thou which means quite a bit of sanding. So what I did on side 1 and am repeating but doing better on side 2 is start with the drum 36 grit to get the finished of and grooves out, then 60 grit. Attachment: 20240630_144613.jpg [ 2.7 MiB | Viewed 65 times ] Then rent the edger and same 36, 60 where the drum couldn't get. Attachment: 20240701_220450.jpg [ 2.77 MiB | Viewed 65 times ] Next they have a 3 pad orbital, I'll do 60 and 100 with that and same along the edges with a 5" orbital.. I know pros will do the finish with the drum and edger, but I'm no pro and as you say the orbitals are much more user friendly. Then a defect inspection...fill anything that needs it, blend out any dings. Then 2 applications of a 2 step product (so 4 coats) called red out that gets rid of the red from the red oak. Dry 24 hours but that is a water base that raise gain so next a VERY light sand by with the 5" and 150 grit taking care not to get back into the red. Then a sealer that prevents the poly from getting into the wood and bringing up it's colors, then 2 layers of a catalyzed commercial poly (which is basically 4 coats of normal poly) with a 150 grit sand between coats and it's a "natural" floor that is anything but natural. Attachment: 20240613_084411.jpg [ 2.01 MiB | Viewed 65 times ] |
|
| Author: | MerlinTech [ Tue Jul 02, 2024 6:09 am ] |
| Post subject: | Re: FrankenFerrari - V12 ferrari 308 part 4 |
Damn man, its no wonder you are not in the shop. That is a ton of refinishing work. That is a crazy process. I feel for you. 
|
|
| Author: | mk e [ Wed Jul 03, 2024 6:23 pm ] |
| Post subject: | Re: FrankenFerrari - V12 ferrari 308 part 4 |
MerlinTech wrote: Damn man, its no wonder you are not in the shop. That is a ton of refinishing work. That is a crazy process. I feel for you. I think the sanding is done now at least, maybe start the finish process tonight. All that time mindlessly sanding has me thinking I should upgrade the alternator before the engine goes back in. I'm sure its marginal at this point and I have a plan forming in my head that involve an electric AC compressor. I see a 12V 3speed unit on ebay for $500-$600 that is probably big enough....1140W, so like 85A, although the word say 35-66A input which seems to not match the rpm/power required chart. Anyway, I would need a much higher output alternator is the point. |
|
| Page 226 of 226 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|